[Armadillo:06627] Re: Debian lenny用linuxカーネルインストールに関して

2011年 1月 25日 (火) 11:31:45 JST

上村様

天城です。

「netflash -knusr /dev/flash/kernel /mnt/linux.bin.gz」を実行したとこ
ろ」とありますが、

USBでDebian lennyを起動したときのエラーですよね？

こちらも似たような症状がでてます。

たしか、USB　SSDでは起動できたのですが、USBメモリで起動できなかったよう
な記憶が・・・
USBで起動させるには何かしなければなかったような気がします。

こちらは、時間が取れたときに、microSDに書き込んで実行してみるつもりです。

(2011/01/25 11:19), email@hidden wrote:
>  
> 竹之下様へ
>
> いつもお忙しいところ、対応「して頂いて有難う御座います。
> ご指示して頂いた手法の「2.2. ArmadilloにUSBメモリを接続して(USBメモリを/mntディレクトリにマウントして)
>      netflash -knusr /dev/flash/kernel /mnt/linux.bin.gz」を実行したところ、以下のメッセージが表示され、処理が止まってしまいました。
>
> Kernel panic - not syncing: Attempted to kill init!
>
> 次にどのように対応したらよいかを、ご教示頂けないでしょうか。
> 宜しくお願い致します。
>
>
> /*************** netflash -knusr /dev/flash/kernel /mnt/linux.bin.gz実行の出力メッセージ*****************/
> [email@hidden (ttymxc0) /mnt]# netflash -knusr /dev/flash/kernel /mnt/linux.bin.gz
> ...........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................!
 ...
>  .........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
> netflash: got "/mnt/linux.bin.gz", length=1708040
> umount: /dev/sdb1 busy - remounted read-only
> netflash: programming FLASH device /dev/flash/kernel
> ..............
> Restarting system.
> Hermit-At v1.1.22 (Armadillo-500/fx 532MHz) compiled at 18:38:09, Feb  1 2010
> Uncompressing  kernel..........................................................................................................done.
> Uncompressing ramdisk.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................done.
> Linux version 2.6.26-at13 (2.6.26) (email@hidden) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #1 PREEMPT Thu Jan 20 17:40:32 JST 2011
> CPU: ARMv6-compatible processor [4107b364] revision 4 (ARMv6TEJ), cr=00e5387f
> Machine: Armadillo-500 FX
> Memory policy: ECC disabled, Data cache writeback
> CPU0: D VIPT write-back cache
> CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
> CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
> Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
> Kernel command line: console=ttymxc0,115200 usb-storage.delay_use=0
> MXC IRQ initialized
> PID hash table entries: 512 (order: 9, 2048 bytes)
> MXC GPT timer initialized, rate = 60000000
> Console: colour dummy device 80x30
> Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
> Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
> Memory: 128MB = 128MB total
> Memory: 107500KB available (3120K code, 200K data, 132K init)
> Mount-cache hash table entries: 512
> CPU: Testing write buffer coherency: ok
> net_namespace: 480 bytes
> NET: Registered protocol family 16
> L2X0 cache controller enabled
> CPU is i.MX31 Revision 2.0
> Clock input source is 26000000
> MXC GPIO hardware
> Using SDMA I.API
> MXC DMA API initialized
> SCSI subsystem initialized
> CSPI: mxc_spi-2 probed
> usbcore: registered new interface driver usbfs
> usbcore: registered new interface driver hub
> usbcore: registered new device driver usb
> MXC I2C driver
> MXC I2C driver
> clk: Unable to get requested clock: dfm_clk
> NET: Registered protocol family 2
> IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
> TCP established hash table entries: 4096 (order: 3, 32768 bytes)
> TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
> TCP: Hash tables configured (established 4096 bind 4096)
> TCP reno registered
> NET: Registered protocol family 1
> checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
> Freeing initrd memory: 18844K
> usb: Host 2 host (isp1504) registered
> usb: Host 1 host (serial) registered
> usb: OTG host (isp1504) registered
> Low-Level PM Driver module loaded
> DPTC driver module loaded
> msgmni has been set to 246
> io scheduler noop registered
> io scheduler cfq registered (default)
> MXC/iMX Backlight Driver
> Console: switching to colour frame buffer device 80x30
> mxcfb: fb registered, using mode KYOCERA-VGA
> Serial: MXC Internal UART driver
> mxcintuart.0: ttymxc0 at MMIO 0x43f90000 (irq = 45) is a Freescale MXC
> console [ttymxc0] enabled
> mxcintuart.1: ttymxc1 at MMIO 0x43f94000 (irq = 32) is a Freescale MXC
> mxcintuart.4: ttymxc4 at MMIO 0x43fb4000 (irq = 47) is a Freescale MXC
> brd: module loaded
> loop: module loaded
> wsim_pm: W-SIM Power Management for i.MX31
> PPP generic driver version 2.4.2
> smsc911x: Driver version 2008-10-21.
> smsc911x-mdio: probed
> eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, irq=-1)
> net eth0: MAC Address: 00:11:0c:0c:04:b7
> Driver 'sd' needs updating - please use bus_type methods
> armadillo5x0-nor: Found 1 x16 devices at 0x0 in 16-bit bank
>  Intel/Sharp Extended Query Table at 0x010A
>  Intel/Sharp Extended Query Table at 0x010A
>  Intel/Sharp Extended Query Table at 0x010A
>  Intel/Sharp Extended Query Table at 0x010A
>  Intel/Sharp Extended Query Table at 0x010A
> Using buffer write method
> Using auto-unlock on power-up/resume
> cfi_cmdset_0001: Erase suspend on write enabled
> armadillo-nor: use default partitions(4)
> Creating 4 MTD partitions on "armadillo5x0-nor":
> 0x00000000-0x00020000 : "nor.bootloader"
> 0x00020000-0x00220000 : "nor.kernel"
> 0x00220000-0x01fe0000 : "nor.userland"
> 0x01fe0000-0x02000000 : "nor.config"
> fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
> fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
> fsl-ehci fsl-ehci.0: irq 36, io mem 0x43f88400
> fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 1 port detected
> Initializing USB Mass Storage driver...
> usbcore: registered new interface driver usb-storage
> USB Mass Storage support registered.
> MXC keypad loaded
> input: mxckpd as /devices/virtual/input/input0
> ads7846 spi3.1: touchscreen, irq 130
> input: ADS784x Touchscreen as /devices/platform/mxc_spi.2/spi3.1/input/input1
> rtc-s353xxa 1-0030: rtc core: registered rtc-s353xxa as rtc0
> rtc-s353xxa: S-353XXA Real Time Clock class driver, (C) 2008 Atmark Techno, Inc.
> i2c /dev entries driver
> MXC MMC/SD driver
> mxcmci-0 found
> mxcmci-1 found
> Registered led device: status
> usb 1-1: new high speed USB device using fsl-ehci and address 2
> usb 1-1: configuration #1 chosen from 1 choice
> scsi0 : SCSI emulation for USB Mass Storage devices
> usbcore: registered new interface driver usbhid
> usbhid: v2.6:USB HID core driver
> SSI module loaded successfully
> Advanced Linux Sound Architecture Driver Version 1.0.16.
> ASoC version 0.13.2
> wm8978: WM8978 Audio Codec v0.2
> scsi 0:0:0:0: Direct-Access     Intel    Value SSD        2.00 PQ: 0 ANSI: 2
> asoc: WM8978 HiFi <-> imx-i2s-1 mapping ok
> sd 0:0:0:0: [sda] 2006016 512-byte hardware sectors (1027 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Assuming drive cache: write through
> sd 0:0:0:0: [sda] 2006016 512-byte hardware sectors (1027 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Assuming drive cache: write through
>  sda: sda1
> sd 0:0:0:0: [sda] Attached SCSI disk
> sd 0:0:0:0: Attached scsi generic sg0 type 0
> ALSA device list:
>   #0: armadillo500fx (WM8978)
> ip_tables: (C) 2000-2006 Netfilter Core Team
> TCP cubic registered
> NET: Registered protocol family 17
> NET: Registered protocol family 15
> VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 2
> rtc-s353xxa 1-0030: setting system clock to 2000-04-26 00:53:09 UTC (956710389)
> RAMDISK: ext2 filesystem found at block 0
> RAMDISK: Loading 18844KiB [1 disk] into ram disk... done.
> VFS: Mounted root (ext2 filesystem).
> Freeing init memory: 132K
> Kernel panic - not syncing: Attempted to kill init!　/*ここがメッセージの最後です*/
>
>
>
>
> 以上です。
>
>
>
>
>
>
>
> -----Original Message-----
> From: email@hidden [mailto:email@hidden] On Behalf Of Takenoshita Koyo
> Sent: Friday, January 21, 2011 6:38 PM
> To: Armadillo series general discussion list
> Subject: [Armadillo:06609] Re: Debian lenny用linuxカーネルインストールに関して
>
> 竹之下です。
>
> Armadilloのフラッシュメモリを書き換える方法は、いくつかあります。
>
> 1. Armadilloを保守モードで起動して
> 1.1. Armadilloと作業用PCをシリアルケーブルで接続して
>      作業用PCでhermit downloadコマンドを実行する。
> 1.2. Armadilloと作業用PCをLANケーブルで接続して
>      Armadilloでtftpdlコマンドを実行する。
>
> 2. Armadilloを(Debianではなく)標準のユーザーランドで起動して
> 2.1. Armadilloと作業用PCをLANケーブルで接続して
>      netflash -knusr /dev/flash/kernel http://(作業用PCのIPアドレス)/linux.bin.gzを実行する。
> 2.2. ArmadilloにUSBメモリを接続して(USBメモリを/mntディレクトリにマウントして)
>      netflash -knusr /dev/flash/kernel /mnt/linux.bin.gz
>
> 今回は、2.2.の方法が使えるのではないかと思います。
>
> email@hidden さんは書きました:
>> いつもお世話になっております。
>> 東芝の上村です。
>>  
>> お忙しい中、いつもご対応して頂き有難う御座います。
>>  
>> 「Armadillo-500 FX 液晶モデルでDebian lennyを使うhttp://armadillo.atmark
>> -techno.com/howto/a500fx-debian-lenny-x#step1」の2.カーネルのビルドにお
>> いて、カーネルイメージ linux-2.6.26-at13/linux.bin.gz をArmadilloのフ
>> ラッシュメモリのカーネル領域へ書き込む場合、通常は、hermit　downloadコマ
>> ンドを使用すると考えますが、都合によりUSBメモリを使って書き込みたいと考
>> えております。Debian lennyがArmadillo500FXにインストールされた状態で、ど
>> このフォルダへ何をコピーすればよいかをご教示頂け無いでしょうか？
>>  
>> 以上、よろしくお願い致します。
>>  
>>  
>>
>>
>>  
>>
>>
>> ----------------------------------------------------------------------
>> --
>>
>> _______________________________________________
>> armadillo mailing list
>> email@hidden
>> http://lists.atmark-techno.com/cgi-bin/mailman/listinfo/armadillo
>
> --
> Koyo Takenoshita
>
> _______________________________________________
> armadillo mailing list
> email@hidden
> http://lists.atmark-techno.com/cgi-bin/mailman/listinfo/armadillo
> _______________________________________________
> armadillo mailing list
> email@hidden
> http://lists.atmark-techno.com/cgi-bin/mailman/listinfo/armadillo
>
>