(double precision)
JFFS2 version 2.2. (NAND) 息 2001-2006 Red Hat, Inc.
msgmni has been set to 57
io scheduler noop registered
io scheduler cfq registered (default)
gpio: Armadillo-2x0 GPIO driver, (C) 2005-2006,2009 Atmark Techno, Inc.
led: Armadillo-2x0 LED driver, (C) 2005-2006,2009 Atmark Techno, Inc.
Serial: AMBA driver $Revision: 1.41 $
apb:uart1: ttyAM0 at MMIO 0x808c0000 (irq = 52) is a AMBA
console [ttyAM0] enabled
apb:uart2: ttyAM1 at MMIO 0x808d0000 (irq = 54) is a AMBA
apb:uart3: ttyAM2 at MMIO 0x808e0000 (irq = 55) is a AMBA
brd: module loaded
loop: module loaded
Driver 'sd' needs updating - please use bus_type methods
armadillo2x0-nor: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
armadillo2x0-nor: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
4 cmdlinepart partitions found on MTD device armadillo2x0-nor
armadillo2x0-nor: use cmdline partitions(4)
Creating 4 MTD partitions on "armadillo2x0-nor":
0x00000000-0x00010000 : "bootloader"
0x00010000-0x00180000 : "kernel"
0x00180000-0x007f0000 : "userland"
0x007f0000-0x00800000 : "config"
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd: block sizes: ed 64 td 64
ep93xx-ohci ep93xx-ohci: EP93xx OHCI
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
ep93xx-ohci ep93xx-ohci: new USB bus registered, assigned bus number 1
ep93xx-ohci ep93xx-ohci: irq 56, io mem 0x80020000
ep93xx-ohci ep93xx-ohci: created debug files
ep93xx-ohci ep93xx-ohci: OHCI controller state
ep93xx-ohci ep93xx-ohci: OHCI 1.0, NO legacy support registers
ep93xx-ohci ep93xx-ohci: control 0x083 HCFS=operational CBSR=3
ep93xx-ohci ep93xx-ohci: cmdstatus 0x00000 SOC=0
ep93xx-ohci ep93xx-ohci: intrstatus 0x00000004 SF
ep93xx-ohci ep93xx-ohci: intrenable 0x8000005a MIE RHSC UE RD WDH
ep93xx-ohci ep93xx-ohci: hcca frame #0005
ep93xx-ohci ep93xx-ohci: roothub.a 02001203 POTPGT=2 NOCP NPS NDP=3(3)
ep93xx-ohci ep93xx-ohci: roothub.b 00000000 PPCM=0000 DR=0000
ep93xx-ohci ep93xx-ohci: roothub.status 00008000 DRWE
ep93xx-ohci ep93xx-ohci: roothub.portstatus [0] 0x00000100 PPS
ep93xx-ohci ep93xx-ohci: roothub.portstatus [1] 0x00010101 CSC PPS CCS
ep93xx-ohci ep93xx-ohci: roothub.portstatus [2] 0x00000100 PPS
usb usb1: default language 0x0409
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: no over-current protection
hub 1-0:1.0: power on to power good time: 4ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: trying to enable port power on non-switchable hub
hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0000
drivers/usb/core/inode.c: creating file '001'
ep93xx-ohci ep93xx-ohci: GetStatus roothub.portstatus [1] = 0x00010101 CSC PPS CCS
hub 1-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EP93xx OHCI
usb usb1: Manufacturer: Linux 2.6.26-at4-ep93xx-port-pre1 ohci_hcd
usb usb1: SerialNumber: ep93xx
Initializing USB Mass Storage driver...
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
ep93xx-ohci ep93xx-ohci: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
usb 1-2: new full speed USB device using ep93xx-ohci and address 2
ep93xx-ohci ep93xx-ohci: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
usb 1-2: ep0 maxpacket = 8
usb 1-2: skipped 1 descriptor after interface
usb 1-2: default language 0x0409
usb 1-2: uevent
usb 1-2: usb_probe_device
usb 1-2: configuration #1 chosen from 1 choice
usb 1-2: adding 1-2:1.0 (config #1, interface 0)
usb 1-2:1.0: uevent
drivers/usb/core/inode.c: creating file '002'
usb 1-2: New USB device found, idVendor=1234, idProduct=0001
usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-2: Product: Product-Name
usb 1-2: Manufacturer: Vendor-Name
hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0004
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
input: tactsw1 as /devices/platform/ep93xx-sw.0/input/input0
i2c-gpio i2c-gpio.0: using pins 12 (SDA) and 13 (SCL)
Registered led device: red
Registered led device: green
usbhid 1-2:1.0: usb_probe_interface
usbhid 1-2:1.0: usb_probe_interface - got id
HID device claimed by neither input, hiddev nor hidraw
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
ep93xx-eth version 0.1 loading
eth0: ep93xx on-chip ethernet, IRQ 39, 00:11:0c:04:31:2e.
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 6071KiB [1 disk] into ram disk... done.
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 104K
ep93xx-ohci ep93xx-ohci: urb c16f2e40 path 2 ep1in 5c160000 cc 5 --> status -62
hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0004
ep93xx-ohci ep93xx-ohci: GetStatus roothub.portstatus [1] = 0x00030100 PESC CSC PPS
hub 1-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
usb 1-2: USB disconnect, address 2
usb 1-2: unregistering device
usb 1-2: usb_disable_device nuking all URBs
usb 1-2: unregistering interface 1-2:1.0
usb 1-2:1.0: uevent
usb 1-2: uevent
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0004
ep93xx-ohci ep93xx-ohci: GetStatus roothub.portstatus [1] = 0x00010101 CSC PPS CCS
hub 1-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
ep93xx-ohci ep93xx-ohci: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
usb 1-2: new full speed USB device using ep93xx-ohci and address 3
ep93xx-ohci ep93xx-ohci: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
usb 1-2: ep0 maxpacket = 8
usb 1-2: skipped 1 descriptor after interface
usb 1-2: default language 0x0409
usb 1-2: uevent
usb 1-2: usb_probe_device
usb 1-2: configuration #1 chosen from 1 choice
usb 1-2: adding 1-2:1.0 (config #1, interface 0)
usb 1-2:1.0: uevent
usbhid 1-2:1.0: usb_probe_interface
usbhid 1-2:1.0: usb_probe_interface - got id
HID device claimed by neither input, hiddev nor hidraw
drivers/usb/core/inode.c: creating file '003'
usb 1-2: New USB device found, idVendor=1234, idProduct=0001
usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-2: Product: Product-Name
usb 1-2: Manufacturer: Vendor-Name
hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0004



dev->filename=003
dev->num_children=0

dev->usb_device_descriptor start
dev->descriptor.bLength=18
dev->descriptor.bDescriptorType=1
dev->descriptor.bcdUSB=512
dev->descriptor.bDeviceClass=0
dev->descriptor.bDeviceSubClass=0
dev->descriptor.bDeviceProtocol=0
dev->descriptor.bMaxPacketSize0=8
dev->descriptor.idVendor=4660
dev->descriptor.idProduct=1
dev->descriptor.bcdDevice=1
dev->descriptor.iManufacturer=1
dev->descriptor.iProduct=2
dev->descriptor.iSerialNumber=0
dev->descriptor.bNumConfigurations=1

dev->usb_config_descriptor start
dev->config->bLength=9
dev->config->bDescriptorType=2
dev->config->wTotalLength=41
dev->config->bNumInterfaces=1
dev->config->bConfigurationValue=1
dev->config->iConfiguration=0
dev->config->bmAttributes=160
dev->config->MaxPower=50
dev->config->extra=(null)
dev->config->extralen=0

dev->usb_config_descriptor->usb_interface start
dev->config->interface.num_altsetting=1

dev->usb_config_descriptor->usb_interface->usb_interface_descriptor start
dev->config->interface->altsetting->bLength=9
dev->config->interface->altsetting->bDescriptorType=4
dev->config->interface->altsetting->bInterfaceNumber=0
dev->config->interface->altsetting->bAlternateSetting=0
dev->config->interface->altsetting->bNumEndpoints=2
dev->config->interface->altsetting->bInterfaceClass=3
dev->config->interface->altsetting->bInterfaceSubClass=0
dev->config->interface->altsetting->bInterfaceProtocol=0
dev->config->interface->altsetting->iInterface=0
dev->config->interface->altsetting->extra=      !
dev->config->interface->altsetting->extralen=9

dev->usb_config_descriptor->usb_interface->usb_interface_descriptor->usb_endpoint_descriptor start
dev->config->interface->altsetting->endpoint->bLength=7
dev->config->interface->altsetting->endpoint->bDescriptorType=5
dev->config->interface->altsetting->endpoint->bEndpointAddress=129
dev->config->interface->altsetting->endpoint->bmAttributes=3
dev->config->interface->altsetting->endpoint->wMaxPacketSize=64
dev->config->interface->altsetting->endpoint->bInterval=1
dev->config->interface->altsetting->endpoint->bRefresh=0
dev->config->interface->altsetting->endpoint->bSynchAddress=0
dev->config->interface->altsetting->endpoint->extra=(null)
dev->config->interface->altsetting->endpoint->extralen=0