[Suzaku:01103] Re: コンフィグレーション
mio
email@hidden
2007年 12月 21日 (金) 14:14:37 JST
中島です。
> 青山と申します。
> 初心者でありながら、大胆にSUZAKUに自作CRTCを作って乗せよ
> うと考えています。ISEで基本信号作りまして、パターンとし
> ては動作しているようです。ただし、DOTクロックにSYS_CLK(
> てい倍前)使ったので、えらい間延びしています。
>
> そこで、EDKでSYS_CLK(CPU_CLK)を2分周してDOTクロックを
> 作ることにして設計し、VHDLの読み込みやピン定義などしてBITSTREAM
> までできました。
>
> 残りはコンフィグレーションですが、以下のようにメッセージ
> 出ます。
> ここから先どの辺チェックすればよろしいでしょうか
>
> At Local date and time: Fri Dec 21 12:34:17 2007
> xbash -q -c "cd /cygdrive/c/suzaku/CRTC_1217_EDK/;
> /usr/bin/make -f xps_proj.make download; exit;" started...
>
> *********************************************
> Downloading Bitstream onto the target board
> *********************************************
> impact -batch etc/download.cmd
>
> Release 9.1.02i - iMPACT J.33
> Copyright (c) 1995-2007 Xilinx, Inc. All rights reserved.
>
> AutoDetecting cable. Please wait.
>
> Connecting to cable (Parallel Port - LPT1).
> Checking cable driver.
> Driver windrvr6.sys version = 8.1.0.0. WinDriver v8.10
> Jungo (c) 1997 - 2006 Build Date: Aug 15 2006 X86 32bit
> SYS
> 14:21:34, version = 810.
> LPT base address = 0378h.
> ECP base address = 0778h.
> Cable connection established.
> Identifying chain contents ....Version is 0000
> '1': : Manufacturer's ID =Xilinx xc3s1200e, Version : 0
>
> INFO:iMPACT:1777 -
> Reading c:/Xilinx91i/spartan3e/data/xc3s1200e.bsd...
>
> INFO:iMPACT:501 - '1': Added Device xc3s1200e
> successfully.
> ----------------------------------------------------------------------
> ----------------------------------------------------------------------
> done.
> Elapsed time = 0 sec.
> Elapsed time = 0 sec.
> '1': Loading file 'implementation/download.bit' ...
>
> done.
>
> WARNING:iMPACT:2257 - Startup Clock has been changed to
> 'JtagClk' in the
> bitstream stored in memory,
> but the original bitstream file remains unchanged.
> INFO:iMPACT:501 - '1': Added Device xc3s1200e
> successfully.
> ----------------------------------------------------------------------
> ----------------------------------------------------------------------
> ----------------------------------------------------------------------
> ----------------------------------------------------------------------
> Maximum TCK operating frequency for this device chain: 0.
> Validating chain...
> Boundary-scan chain validated successfully.
> '1': Programming device...
>
> done.
> '1': Reading status register contents...
> CRC error :
> 0
> Decryptor security set :
> 0
> DCM locked :
> 1
> DCI matched :
> 1
> legacy input error :
> 0
> status of GTS_CFG_B :
> 0
> status of GWE :
> 0
> status of GHIGH :
> 0
> value of MODE pin M0 :
> 1
> value of MODE pin M1 :
> 0
> value of MODE pin M2 :
> 0
> value of CFG_RDY (INIT_B) :
> 0
> DONEIN input from DONE pin :
> 0
> IDCODE not validated while trying to write FDRI :
> 0
> write FDRI issued before or after decrypt operation:
> 0
> Decryptor keys not used in proper sequence :
> 0
> INFO:iMPACT:2219 - Status register values:
> INFO:iMPACT - 0011 0000 1000 0000 0000 0000 0000 0000
> INFO:iMPACT:579 - '1': Completed downloading bit file to
> device.
> INFO:iMPACT - '1': Checking done pin....done.
> '1': Programming terminated. DONE did not go high.
> Elapsed time = 18 sec.
>
>
> Done!
>
ログを読む限りでは、
デバイスは発見されているが
その後の書き込みに失敗している状態のようです。
思いつくのは、ケーブルの接続くらいです。。
使っているのはパラレルケーブルIIIですよね?
一度、他のbitファイルの書き込みはうまくいくのか確認してもらえますか?
昔、書き込めていたbitファイルなどあったらそのファイルでお願いします。
suzaku メーリングリストの案内