[Armadillo:07412] Re: Armadillo-9＋linux-2.6.26-at4-ep93xx-port-pre2にてIDE Diskを認識しない

2011年 7月 25日 (月) 17:01:12 JST

花田です。

> 「Armadillo-9/200シリーズ用カーネル2.6.
> 26(pre2)ベータリリース」でIDE Diskを認識させるために、カーネル設定の変更
> 等が必要であれば教えて頂けないでしょうか？

担当者に確認したのですが、特に設定変更等は必要ないようで…

特定の問題かもしれないなぁ、としかいえない状況です。
可能でしたら、接続したドライブの情報(型番)や、
接続ケーブルなどについて情報いただけますか?

At 25 Jul 2011 16:24:04 +0900 email@hidden wrote:
> suzakiです。
> お世話になっております。
> 
> Armadillo9に2010/8にリリースして頂いた「Armadillo-9/200シリーズ用カーネ
> ル2.6.26(pre2)ベータリリース」のバイナリを使って動作確認をしたのですが、
> 実装済みと記載されているIDEが認識できませんでした。IDE DISKは、CON9ポー
> トにケーブルを介してDISKを接続しております。
> こちらの環境に問題がないか確認するために従来リリース版である「linux-2.6.
> 12.3-a9-at17」のバイナリを使って確認したらIDEポートに接続されているDISK
> をhdaとして正しく認識できました。「Armadillo-9/200シリーズ用カーネル2.6.
> 26(pre2)ベータリリース」でIDE Diskを認識させるために、カーネル設定の変更
> 等が必要であれば教えて頂けないでしょうか？
> 
> 以下はそれぞれのブート・ログです。
> 
> １．2.6.26-at4
> 
> Hermit-At v1.1.21.ep93xx.port.pre2 (armadillo9/eth) compiled at 11:14:21, 
> Aug 17 2010
> Uncompressing  kernel.................................
> ...............................................................done.
> Uncompressing ramdisk.................................
> ......................................................
> .............................................done.
> Doing console=ttyAM0,115200
> Doing mtdparts=armadillo9-nor:0x10000(bootloader)ro,0x200000(kernel),
> 0x5e0000(userland),-(config)
> Linux version 2.6.26-at4-ep93xx-port-pre2 (2.6.26) (email@hidden) (gcc 
> version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 PREEMPT Wed 
> Aug 11 14:21:34 JST 2010
> CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0003177
> Machine: Atmark Techno Armadillo9
> Memory policy: ECC disabled, Data cache writeback
> CPU0: D VIVT write-back cache
> CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
> CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
> Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 
> 16192
> Kernel command line: console=ttyAM0,115200 mtdparts=armadillo9-nor:
> 0x10000(bootloader)ro,0x200000(kernel),0x5e0000(userland),-(config)
> PID hash table entries: 256 (order: 8, 1024 bytes)
> Console: colour dummy device 80x30
> Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
> Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
> Memory: 32MB 32MB = 64MB total
> Memory: 57452KB available (2812K code, 261K data, 128K init)
> Mount-cache hash table entries: 512
> CPU: Testing write buffer coherency: ok
> net_namespace: 480 bytes
> NET: Registered protocol family 16
> ep93xx: PLL1 running at 400 MHz, PLL2 at 192 MHz
> ep93xx: FCLK 200 MHz, HCLK 100 MHz, PCLK 50 MHz
> SCSI subsystem initialized
> usbcore: registered new interface driver usbfs
> usbcore: registered new interface driver hub
> usbcore: registered new device driver usb
> NET: Registered protocol family 2
> IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
> TCP established hash table entries: 2048 (order: 2, 16384 bytes)
> TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
> TCP: Hash tables configured (established 2048 bind 2048)
> TCP reno registered
> NET: Registered protocol family 1
> checking if image is initramfs...it isn't (bad gzip magic numbers); 
> looks like an initrd
> Freeing initrd memory: 4209K
> NetWinder Floating Point Emulator V0.97 (extended precision)
> msgmni has been set to 120
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered (default)
> Console: switching to colour frame buffer device 80x30
> fb0: EP93xx frame buffer at 640x480x16bpp
> Serial: AMBA driver $Revision: 1.41 $
> apb:uart1: ttyAM0 at MMIO 0x808c0000 (irq = 52) is a AMBA
> console [ttyAM0] enabled
> apb:uart2: ttyAM1 at MMIO 0x808d0000 (irq = 54) is a AMBA
> apb:uart3: ttyAM2 at MMIO 0x808e0000 (irq = 55) is a AMBA
> brd: module loaded
> loop: module loaded
> Uniform Multi-Platform E-IDE driver
> ide: Assuming 50MHz system bus speed for PIO modes; override with idebus
> =xx
> ide0 at 0x800-0x807,0x406 on irq 40
> Driver 'sd' needs updating - please use bus_type methods
> armadillo2x0-nor: Found 1 x16 devices at 0x0 in 16-bit bank
>  Amd/Fujitsu Extended Query Table at 0x0040
> armadillo2x0-nor: CFI does not contain boot bank location. Assuming top.
> number of CFI chips: 1
> cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
> armadillo2x0-nor: use default partitions(4)
> Creating 4 MTD partitions on "armadillo2x0-nor":
> 0x00000000-0x00010000 : "bootloader"
> 0x00010000-0x00210000 : "kernel"
> 0x00210000-0x007f0000 : "userland"
> 0x007f0000-0x00800000 : "config"
> GPIO-3 autorequested
> GPIO-22 autorequested
> GPIO-17 autorequested
> GPIO-18 autorequested
> GPIO-20 autorequested
> GPIO-19 autorequested
> ep93xx-ohci ep93xx-ohci: EP93xx OHCI
> ep93xx-ohci ep93xx-ohci: new USB bus registered, assigned bus number 1
> ep93xx-ohci ep93xx-ohci: irq 56, io mem 0x80020000
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 3 ports detected
> usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
> usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
> usb usb1: Product: EP93xx OHCI
> usb usb1: Manufacturer: Linux 2.6.26-at4-ep93xx-port-pre2 ohci_hcd
> usb usb1: SerialNumber: ep93xx
> Initializing USB Mass Storage driver...
> usbcore: registered new interface driver usb-storage
> USB Mass Storage support registered.
> mice: PS/2 mouse device common for all mice
> i2c-gpio i2c-gpio.0: using pins 12 (SDA) and 13 (SCL)
> usbcore: registered new interface driver usbhid
> usbhid: v2.6:USB HID core driver
> ip_tables: (C) 2000-2006 Netfilter Core Team
> TCP cubic registered
> NET: Registered protocol family 17
> NET: Registered protocol family 15
> ep93xx-eth version 0.1 loading
> eth0: ep93xx on-chip ethernet, IRQ 39, 00:11:0c:02:08:b9.
> RAMDISK: ext2 filesystem found at block 0
> RAMDISK: Loading 4209KiB [1 disk] into ram disk... done.
> VFS: Mounted root (ext2 filesystem).
> Freeing init memory: 128K
> 
> 
> ２．2.6.12.3-a9-at17
> Hermit-At v1.1.21 (armadillo9) compiled at 18:39:17, Mar 25 2009
> Uncompressing  kernel.................................
> .......................................................done.
> Uncompressing ramdisk.................................
> ......................................................
> ......................................................
> ....................................................done.
> Doing console=ttyAM0,115200
> Doing mtdparts=armadillo9-nor:0x10000(bootloader)ro,0x170000(kernel),
> 0x670000(userland),-(config)
> Linux version 2.6.12.3-a9-17 (email@hidden) (gcc version 4.1.2 
> 20061115 (prerelease) (Debian 4.1.1-21)) #1 Thu Mar 19 13:47:09 JST 2009
> CPU: ARM920Tid(wb) [41129200] revision 0 (ARMv4T)
> CPU0: D VIVT write-back cache
> CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
> CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
> Machine: Armadillo-9
> Memory policy: ECC disabled, Data cache writeback
> Built 1 zonelists
> Kernel command line: console=ttyAM0,115200 mtdparts=armadillo9-nor:
> 0x10000(bootloader)ro,0x170000(kernel),0x670000(userland),-(config)
> PID hash table entries: 512 (order: 9, 8192 bytes)
> Console: colour dummy device 80x30
> Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
> Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
> Memory: 32MB 32MB = 64MB total
> Memory: 55608KB available (2305K code, 572K data, 100K init)
> Mount-cache hash table entries: 512
> CPU: Testing write buffer coherency: ok
> checking if image is initramfs...it isn't (bad gzip magic numbers); 
> looks like an initrd
> Freeing initrd memory: 6144K
> NET: Registered protocol family 16
> SCSI subsystem initialized
> usbcore: registered new driver usbfs
> usbcore: registered new driver hub
> NetWinder Floating Point Emulator V0.97 (double precision)
> devfs: 2004-01-31 Richard Gooch (email@hidden)
> devfs: boot_options: 0x0
> Console: switching to colour frame buffer device 80x30
> fb0: EP93xx frame buffer at 640x480x16
> ttyAM0 at MMIO 0x808c0000 (irq = 52) is a EP93XX
> ttyAM1 at MMIO 0x808d0000 (irq = 54) is a EP93XX
> ttyAM2 at MMIO 0x808e0000 (irq = 55) is a EP93XX
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered
> RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
> loop: loaded (max 8 devices)
> i2c /dev entries driver
> i2c-armadillo9: i2c Armadillo-9 driver, (C) 2004-2007 Atmark Techno, Inc.
> i2c-at24cxx: i2c at24cxx eeprom driver, (C) 2003-2005 Atmark Techno, Inc.
> i2c-s3531a: Device Type [S-353x0A]
> i2c-s3531a: i2c S-3531A/S-353X0A driver, (C) 2001-2005 Atmark Techno, 
> Inc.
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 50MHz system bus speed for PIO modes; override with idebus
> =xx
> No card in slot: PFDR=000000ff
> hda: SanDisk SDCFJ-32, CFA DISK drive
> ide0 at 0x800-0x807,0x406 on irq 40
> hda: max request size: 128KiB
> hda: 62720 sectors (32 MB) w/1KiB Cache, CHS=490/4/32
> hda: cache flushes not supported
>  /dev/ide/host0/bus0/target0/lun0: p1
> armadillo9-nor: Found 1 x16 devices at 0x0 in 16-bit bank
>  Amd/Fujitsu Extended Query Table at 0x0040
> armadillo9-nor: CFI does not contain boot bank location. Assuming top.
> number of CFI chips: 1
> cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
> 4 cmdlinepart partitions found on MTD device armadillo9-nor
> parse_mtd_partitions:4
> Creating 4 MTD partitions on "armadillo9-nor":
> 0x00000000-0x00010000 : "bootloader"
> 0x00010000-0x00180000 : "kernel"
> 0x00180000-0x007f0000 : "userland"
> 0x007f0000-0x00800000 : "config"
> ep93xxusb ep93xxusb.0: EP93xx OHCI
> ep93xxusb ep93xxusb.0: new USB bus registered, assigned bus number 1
> ep93xxusb ep93xxusb.0: irq 56, io base 0xff020000
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 3 ports detected
> usbcore: registered new driver audio
> drivers/usb/class/audio.c: v1.0.0:USB Audio Class driver
> Initializing USB Mass Storage driver...
> usbcore: registered new driver usb-storage
> USB Mass Storage support registered.
> usbcore: registered new driver usbhid
> drivers/usb/input/hid-core.c: v2.01:USB HID core driver
> usbcore: registered new driver usbserial
> drivers/usb/serial/usb-serial.c: USB Serial support registered for 
> Generic
> usbcore: registered new driver usbserial_generic
> drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
> mice: PS/2 mouse device common for all mice
> NET: Registered protocol family 2
> IP: routing cache hash table of 512 buckets, 4Kbytes
> TCP established hash table entries: 4096 (order: 3, 32768 bytes)
> TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
> TCP: Hash tables configured (established 4096 bind 4096)
> ip_tables: (C) 2000-2002 Netfilter core team
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> RAMDISK: ext2 filesystem found at block 0
> RAMDISK: Loading 6144KiB [1 disk] into ram disk... done.
> VFS: Mounted root (ext2 filesystem).
> Freeing init memory: 100K
> 
> 以上
> _______________________________________________
> armadillo mailing list
> email@hidden
> http://lists.atmark-techno.com/cgi-bin/mailman/listinfo/armadillo
> 

____________________________________________________

    花田 政弘 (はなだ まさひろ)

      (株)アットマークテクノ 開発部
        TEL: 011-207-6550    FAX: 011-207-6570
        URL: http://www.atmark-techno.com/

    E-mail: email@hidden
____________________________________________________