[Suzaku:01713] Re: SZ130_SILの赤LEDについて
Chie Aoki
email@hidden
2009年 12月 15日 (火) 14:49:34 JST
青木です。
ありがとうございます。
これまで試したことをまとめてみます。
1.TCK Speed/Baud Rate を下げる
(http://lists.atmark-techno.com/pipermail/suzaku/2007-August/001011.html)
2.JTAGの電源コードをLED/SW基板につなげる
(http://lists.atmark-techno.com/pipermail/suzaku/2007-August/001000.html)
3.Platform Cable USBを使う場合の書込み方法を試す
(http://suzaku.atmark-techno.com/dev/howtos/PlatformCableUSB)
どの方法を試しても、iMPACTで、「Program Faild」と表示されてしまいます。
iMPACTの立ち上げから書込み失敗まで、下のようなメッセージが出ます。
JTAG-CLKを下げて、コンソールの出力内容が途中で止まることはありません。
何かほかに気付いたことがあったらご連絡いただけると助かります。
よろしくお願い致します。
Enumerating cables. Please wait.
PROGRESS_START - Starting Operation.
Connecting to cable (Usb Port - USB21).
Checking cable driver.
Driver file xusb_xlp.sys found.
Driver version: src=1029, dest=1029.
Driver windrvr6.sys version = 8.1.1.0. WinDriver v8.11 Jungo (c) 1997 -
2006 Build Date: Oct 16 2006 X86 32bit SYS 12:35:07, version = 811.
Cable PID = 0008.
Max current requested during enumeration is 74 mA.
Type = 0x0004.
Cable Type = 3, Revision = 0.
Setting cable speed to 6 MHz.
Cable connection established.
Firmware version = 1303.
File version of C:/Xilinx/10.1/ISE/data/xusb_xlp.hex = 1303.
Firmware hex file version = 1303.
=======================================================
Found cable - > Type = 0x0004.
ESN option: 00001024272201.
ESN = 00001024272201.
=======================================================
Connecting to cable (Usb Port - USB22).
Checking cable driver.
Driver file xusb_xlp.sys found.
Driver version: src=1029, dest=1029.
Driver windrvr6.sys version = 8.1.1.0. WinDriver v8.11 Jungo (c) 1997 -
2006 Build Date: Oct 16 2006 X86 32bit SYS 12:35:07, version = 811.
Cable connection failed.
PROGRESS_END - End Operation.
Elapsed time = 3 sec.
Error opening cdb file for reading.
Connecting to cable (Usb Port - USB21).
Checking cable driver.
Driver file xusb_xlp.sys found.
Driver version: src=1029, dest=1029.
Driver windrvr6.sys version = 8.1.1.0. WinDriver v8.11 Jungo (c) 1997 -
2006 Build Date: Oct 16 2006 X86 32bit SYS 12:35:07, version = 811.
Cable PID = 0008.
Max current requested during enumeration is 74 mA.
Type = 0x0004.
Cable Type = 3, Revision = 0.
Setting cable speed to 1.5 MHz.
Cable connection established.
Firmware version = 1303.
File version of C:/Xilinx/10.1/ISE/data/xusb_xlp.hex = 1303.
Firmware hex file version = 1303.
PLD file version = 0012h.
PLD version = 0012h.
Type = 0x0004.
ESN option: 00001024272201.
Maximum TCK operating frequency for this device chain: 10000000.
Validating chain...
Boundary-scan chain validated successfully.
'1': Programming device...
PROGRESS_START - Starting Operation.
done.
'1': Reading status register contents...
CRC error : 0
Decryptor security set : 0
DCM locked : 1
DCI matched : 1
legacy input error : 0
status of GTS_CFG_B : 1
status of GWE : 1
status of GHIGH : 1
value of MODE pin M0 : 1
value of MODE pin M1 : 1
value of MODE pin M2 : 1
value of CFG_RDY (INIT_B) : 1
DONEIN input from DONE pin : 1
IDCODE not validated while trying to write FDRI : 0
write FDRI issued before or after decrypt operation: 0
Decryptor keys not used in proper sequence : 0
INFO:iMPACT:2219 - Status register values:
INFO:iMPACT - 0011 0111 1111 1000 0000 0000 0000 0000
INFO:iMPACT:579 - '1': Completed downloading bit file to device.
INFO:iMPACT - '1': Checking done pin....done.
'1': Programming terminated. DONE did not go high.
PROGRESS_END - End Operation.
Elapsed time = 4 sec.
suzaku メーリングリストの案内