[Armadillo:07621] eth0 デバイス認識せず: Armadillo-500FX量産ボード Debian lennyにて

[天晴]

お世話になります、天城です。

Armadillo-500FX液晶モデル開発キットと、
量産ボード＋LCD IFボードにてDebian lennyを動かしてます。

同じカーネル＆microSDを使って、両方のボードを起動させると
量産ボードのほうだけ、ネットワークが起動しません。
デバイスが認識できないようです。

もしかして、Debian lennyでカーネルを構築するときに、
量産ボードの場合

make armadillo500fx_dev_defconfig

では、問題あるのでしょうか？

量産ボードでエラーが出てる部分です。

Loading kernel modules...FATAL: Could not load
/lib/modules/2.6.26-at13/modules.dep: No such file or directory
Checking file systems...fsck 1.41.3 (12-Oct-2008)
done.
Setting kernel variables (/etc/sysctl.conf)...done.
Mounting local filesystems...done.
Activating swapfile swap...done.
Setting up networking....
Configuring network interfaces...modprobe: FATAL: Could not load
/lib/modules/2.6.26-at13/modules.dep: No such file or directory

SIOCSIFADDR: No such device
modprobe: FATAL: Could not load /lib/modules/2.6.26-at13/modules.dep: No
such file or directory

eth0: ERROR while getting interface flags: No such device
modprobe: FATAL: Could not load /lib/modules/2.6.26-at13/modules.dep: No
such file or directory

SIOCSIFNETMASK: No such device
modprobe: FATAL: Could not load /lib/modules/2.6.26-at13/modules.dep: No
such file or directory

SIOCSIFBRDADDR: No such device
modprobe: FATAL: Could not load /lib/modules/2.6.26-at13/modules.dep: No
such file or directory

eth0: ERROR while getting interface flags: No such device
modprobe: FATAL: Could not load /lib/modules/2.6.26-at13/modules.dep: No
such file or directory

eth0: ERROR while getting interface flags: No such device
Failed to bring up eth0.
done.



尚、どちらのシステムでもGUIは問題なく
動いております。

「Loading kernel modules...FATAL: Could not load
/lib/modules/2.6.26-at13/modules.dep: No such file or directory
」

と言う、エラーメッセージも気になります。同じmicroSDを使ってるのに
量産ボードだけこのエラーが出ます。
2.6.26-at13ですが、microSDの中には2.6.26-at6のディレクトリしか
存在しません。開発キットはエラーが出ないのも不思議です。

最後に、両方の起動時のログを載せておきます。

--------- 量産ボード --------------
INIT: Switching to runlevel: 6
INIT: Sending processes the TERM signal
Stopping web server: apache2apache2: Could not reliably determine the
server's fully qualified domain name, using 127.0.0.1 for ServerName
... waiting .
Stopping internet superserver: inetd.
Saving the system clock.
Shutting down ALSA...done.
Stopping enhanced syslogd: rsyslogd.
Asking all remaining processes to terminate...xinit: connection to X
server lost.

waiting for X server to shut down done.
FreeFontPath: FPE "/usr/share/fonts/X11/misc" refcount is 2, should be
1; fixing.


xinit: unexpected signal 15.
All processes ended within 2 seconds....done.
Deconfiguring network interfaces...done.
Cleaning up ifupdown....
Deactivating swap...done.
Will now restart.
Restarting system.
Hermit-At v1.1.24 (Armadillo-500/fx 532MHz) compiled at 15:57:27, Mar 24
2011
Uncompressing
kernel..........................................................................................................done.
Doing console=ttymxc0
Doing root=/dev/mmcblk0p1
Doing init=/init
Doing noinitrd
Doing rootwait
Linux version 2.6.26-at13 (2.6.26) (email@hidden) (gcc version 4.3.2
(Debian 4.3.2-1.1) ) #4 PREEMPT Thu Jan 20 11:38:40 JST 2011
CPU: ARMv6-compatible processor [4107b364] revision 4 (ARMv6TEJ),
cr=00e5387f
Machine: Armadillo-500 FX
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIPT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: console=ttymxc0 root=/dev/mmcblk0p1 init=/init
noinitrd rootwait
MXC IRQ initialized
PID hash table entries: 512 (order: 9, 2048 bytes)
MXC GPT timer initialized, rate = 60000000
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 126444KB available (3120K code, 200K data, 132K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 480 bytes
NET: Registered protocol family 16
L2X0 cache controller enabled
CPU is i.MX31 Revision 2.0
Clock input source is 26000000
MXC GPIO hardware
Using SDMA I.API
MXC DMA API initialized
SCSI subsystem initialized
CSPI: mxc_spi-2 probed
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
MXC I2C driver
MXC I2C driver
clk: Unable to get requested clock: dfm_clk
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
usb: Host 2 host (isp1504) registered
usb: Host 1 host (serial) registered
usb: OTG host (isp1504) registered
Low-Level PM Driver module loaded
DPTC driver module loaded
msgmni has been set to 246
io scheduler noop registered
io scheduler cfq registered (default)
MXC/iMX Backlight Driver
Console: switching to colour frame buffer device 80x30
mxcfb: fb registered, using mode KYOCERA-VGA
Serial: MXC Internal UART driver
mxcintuart.0: ttymxc0 at MMIO 0x43f90000 (irq = 45) is a Freescale MXC
console [ttymxc0] enabled
mxcintuart.1: ttymxc1 at MMIO 0x43f94000 (irq = 32) is a Freescale MXC
mxcintuart.4: ttymxc4 at MMIO 0x43fb4000 (irq = 47) is a Freescale MXC
brd: module loaded
loop: module loaded
wsim_pm: W-SIM Power Management for i.MX31
PPP generic driver version 2.4.2
smsc911x: Driver version 2008-10-21.
smsc911x-mdio: probed
eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, irq=-1)
net eth0: MAC Address: 00:11:0c:0c:04:8f
Driver 'sd' needs updating - please use bus_type methods
armadillo5x0-nor: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Using buffer write method
Using auto-unlock on power-up/resume
cfi_cmdset_0001: Erase suspend on write enabled
armadillo-nor: use default partitions(4)
Creating 4 MTD partitions on "armadillo5x0-nor":
0x00000000-0x00020000 : "nor.bootloader"
0x00020000-0x00220000 : "nor.kernel"
0x00220000-0x01fe0000 : "nor.userland"
0x01fe0000-0x02000000 : "nor.config"
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: irq 36, io mem 0x43f88400
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
MXC keypad loaded
input: mxckpd as /devices/virtual/input/input0
ads7846 spi3.1: touchscreen, irq 130
input: ADS784x Touchscreen as
/devices/platform/mxc_spi.2/spi3.1/input/input1
rtc-s353xxa 1-0030: rtc core: registered rtc-s353xxa as rtc0
rtc-s353xxa: S-353XXA Real Time Clock class driver, (C) 2008 Atmark
Techno, Inc.
i2c /dev entries driver
MXC MMC/SD driver
mxcmci-0 found
mxcmci-1 found
Registered led device: status
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
SSI module loaded successfully
Advanced Linux Sound Architecture Driver Version 1.0.16.
ASoC version 0.13.2
wm8978: WM8978 Audio Codec v0.2
asoc: WM8978 HiFi <-> imx-i2s-1 mapping ok
ALSA device list:
#0: armadillo500fx (WM8978)
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 2
rtc-s353xxa 1-0030: setting system clock to 2008-04-04 20:00:17 UTC
(1207339217)
Waiting for root device /dev/mmcblk0p1...
mmc0: host does not support reading read-only switch. assuming write-enable.
mmc0: new SDHC card at address 1234
mmcblk0: mmc0:1234 SA04G 3858432KiB
mmcblk0: p1 p2
kjournald starting. Commit interval 5 seconds
EXT3 FS on mmcblk0p1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem).
Freeing init memory: 132K
Failed to execute /init. Attempting defaults...
modprobe: FATAL: Could not load /lib/modules/2.6.26-at13/modules.dep: No
such file or directory

INIT: version 2.86 booting
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...done.
Setting the system clock.
Activating swap...done.
Checking root file system...fsck 1.41.3 (12-Oct-2008)
xxxxx: clean, 23878/210912 files, 232576/842432 blocks
done.
EXT3 FS on mmcblk0p1, internal journal
Setting the system clock.
Cleaning up ifupdown....
Loading kernel modules...FATAL: Could not load
/lib/modules/2.6.26-at13/modules.dep: No such file or directory
Checking file systems...fsck 1.41.3 (12-Oct-2008)
done.
Setting kernel variables (/etc/sysctl.conf)...done.
Mounting local filesystems...done.
Activating swapfile swap...done.
Setting up networking....
Configuring network interfaces...modprobe: FATAL: Could not load
/lib/modules/2.6.26-at13/modules.dep: No such file or directory

SIOCSIFADDR: No such device
modprobe: FATAL: Could not load /lib/modules/2.6.26-at13/modules.dep: No
such file or directory

eth0: ERROR while getting interface flags: No such device
modprobe: FATAL: Could not load /lib/modules/2.6.26-at13/modules.dep: No
such file or directory

SIOCSIFNETMASK: No such device
modprobe: FATAL: Could not load /lib/modules/2.6.26-at13/modules.dep: No
such file or directory

SIOCSIFBRDADDR: No such device
modprobe: FATAL: Could not load /lib/modules/2.6.26-at13/modules.dep: No
such file or directory

eth0: ERROR while getting interface flags: No such device
modprobe: FATAL: Could not load /lib/modules/2.6.26-at13/modules.dep: No
such file or directory

eth0: ERROR while getting interface flags: No such device
Failed to bring up eth0.
done.
Setting up ALSA...done.
INIT: Entering runlevel: 2
Starting enhanced syslogd: rsyslogd.
Starting system message bus: dbus.
Starting OpenBSD Secure Shell server: sshd.
Preparing /var/run/firebird/2.0...done.
Starting internet superserver: inetd.
Starting periodic command scheduler: crond.
Starting web server: apache2apache2: Could not reliably determine the
server's fully qualified domain name, using 127.0.0.1 for ServerName
.
fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
fsl-ehci fsl-ehci.1: irq 35, io mem 0x43f88200
fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
fsl-ehci fsl-ehci.2: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.2: new USB bus registered, assigned bus number 3
fsl-ehci fsl-ehci.2: irq 37, io mem 0x43f88000
fsl-ehci fsl-ehci.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected

X: warning; process set to priority -1 instead of requested priority 0

X.Org X Server 1.4.2
Release Date: 11 June 2008
X Protocol Version 11, Revision 0
Build Operating System: Linux Debian (xorg-server 2:1.4.2-10.lenny3)
Current Operating System: Linux debian 2.6.26-at13 #4 PREEMPT Thu Jan 20
11:38:40 JST 2011 armv6l
Build Date: 25 September 2010 02:52:58PM

Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Fri Apr 4 20:01:05 2008
(==) Using config file: "/etc/X11/xorg.conf"

X: warning; process set to priority -1 instead of requested priority 0

Fatal server error:
Server is already active for display 0
If this server is no longer running, remove /tmp/.X0-lock
and start again.

xf86optionListCreate: count must be an even number.
State: S_UNTOUCHED Action: No Action Button: 0
State: S_TOUCHED Action: No Action Button: 0
State: S_LONGTOUCHED Action: down Button: 1
State: S_MOVING Action: No Action Button: 0
State: S_MAYBETAPPED Action: click Button: 1
State: S_ONEANDAHALFTAP Action: down Button: 3
[config/hal] couldn't initialise context: (null) ((null))

---------------------------------


--------- 開発キット --------------
INIT: Switching to runlevel: 6
INIT: Sending processes the TERM signal

waiting for X server to shut down error: 'stop-bootlogd' exited outside
the expected code flow.
FreeFontPath: FPE "/usr/share/fonts/X11/misc" refcount is 2, should be
1; fixing.


xinit: unexpected signal 15.
Stopping web server: apache2apache2: Could not reliably determine the
server's fully qualified domain name, using 127.0.0.1 for ServerName
... waiting ..
Stopping internet superserver: inetd.
Saving the system clock.
Shutting down ALSA...done.
Stopping enhanced syslogd: rsyslogd already stopped.
Asking all remaining processes to terminate...done.
All processes ended within 1 seconds....done.
Deconfiguring network interfaces...done.
Cleaning up ifupdown....
Deactivating swap...done.
Will now restart.
Restarting system.
Hermit-At v1.1.21 (Armadillo-500/fx) compiled at 18:40:04, Mar 25 2009
Uncompressing
kernel..........................................................................................................done.
Doing console=ttymxc0
Doing root=/dev/mmcblk0p1
Doing init=/init
Doing noinitrd
Doing rootwait
Linux version 2.6.26-at13 (2.6.26) (email@hidden) (gcc version 4.3.2
(Debian 4.3.2-1.1) ) #4 PREEMPT Thu Jan 20 11:38:40 JST 2011
CPU: ARMv6-compatible processor [4107b364] revision 4 (ARMv6TEJ),
cr=00e5387f
Machine: Armadillo-500 FX
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIPT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: console=ttymxc0 root=/dev/mmcblk0p1 init=/init
noinitrd rootwait
MXC IRQ initialized
PID hash table entries: 512 (order: 9, 2048 bytes)
MXC GPT timer initialized, rate = 60000000
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 126444KB available (3120K code, 200K data, 132K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 480 bytes
NET: Registered protocol family 16
L2X0 cache controller enabled
CPU is i.MX31 Revision 2.0
Clock input source is 26000000
MXC GPIO hardware
Using SDMA I.API
MXC DMA API initialized
SCSI subsystem initialized
CSPI: mxc_spi-2 probed
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
MXC I2C driver
MXC I2C driver
clk: Unable to get requested clock: dfm_clk
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
usb: Host 2 host (isp1504) registered
usb: Host 1 host (serial) registered
usb: OTG host (isp1504) registered
Low-Level PM Driver module loaded
DPTC driver module loaded
msgmni has been set to 246
io scheduler noop registered
io scheduler cfq registered (default)
MXC/iMX Backlight Driver
Console: switching to colour frame buffer device 80x30
mxcfb: fb registered, using mode KYOCERA-VGA
Serial: MXC Internal UART driver
mxcintuart.0: ttymxc0 at MMIO 0x43f90000 (irq = 45) is a Freescale MXC
console [ttymxc0] enabled
mxcintuart.1: ttymxc1 at MMIO 0x43f94000 (irq = 32) is a Freescale MXC
mxcintuart.4: ttymxc4 at MMIO 0x43fb4000 (irq = 47) is a Freescale MXC
brd: module loaded
loop: module loaded
wsim_pm: W-SIM Power Management for i.MX31
PPP generic driver version 2.4.2
smsc911x: Driver version 2008-10-21.
smsc911x-mdio: probed
eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, irq=-1)
net eth0: MAC Address: 00:11:0c:0c:02:ea
Driver 'sd' needs updating - please use bus_type methods
armadillo5x0-nor: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Using buffer write method
Using auto-unlock on power-up/resume
cfi_cmdset_0001: Erase suspend on write enabled
armadillo-nor: use default partitions(4)
Creating 4 MTD partitions on "armadillo5x0-nor":
0x00000000-0x00020000 : "nor.bootloader"
0x00020000-0x00220000 : "nor.kernel"
0x00220000-0x01fe0000 : "nor.userland"
0x01fe0000-0x02000000 : "nor.config"
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: irq 36, io mem 0x43f88400
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
MXC keypad loaded
input: mxckpd as /devices/virtual/input/input0
ads7846 spi3.1: touchscreen, irq 130
input: ADS784x Touchscreen as
/devices/platform/mxc_spi.2/spi3.1/input/input1
rtc-s353xxa 1-0030: rtc core: registered rtc-s353xxa as rtc0
rtc-s353xxa: S-353XXA Real Time Clock class driver, (C) 2008 Atmark
Techno, Inc.
i2c /dev entries driver
MXC MMC/SD driver
mxcmci-0 found
mxcmci-1 found
Registered led device: status
mmc1: host does not support reading read-only switch. assuming write-enable.
mmc1: new SDHC card at address 1234
mmcblk0: mmc1:1234 SA04G 3858432KiB
mmcblk0: p1 p2
usb 1-1: new high speed USB device using fsl-ehci and address 2
usb 1-1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
SSI module loaded successfully
Advanced Linux Sound Architecture Driver Version 1.0.16.
ASoC version 0.13.2
wm8978: WM8978 Audio Codec v0.2
asoc: WM8978 HiFi <-> imx-i2s-1 mapping ok
ALSA device list:
#0: armadillo500fx (WM8978)
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 2
rtc-s353xxa 1-0030: setting system clock to 2011-10-06 14:50:28 UTC
(1317912628)
kjournald starting. Commit interval 5 seconds
EXT3 FS on mmcblk0p1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem).
Freeing init memory: 132K
Failed to execute /init. Attempting defaults...
modprobe: FATAL: Could not load /lib/modules/2.6.26-at13/modules.dep: No
such file or directory

INIT: version 2.86 booting
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...scsi 0:0:0:0: Direct-Access
Intel Value SSD 2.00 PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] 2006016 512-byte hardware sectors (1027 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] 2006016 512-byte hardware sectors (1027 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
done.
Setting the system clock.
Activating swap...done.
Checking root file system...fsck 1.41.3 (12-Oct-2008)
xxxx: clean, 23887/210912 files, 229152/842432 blocks
done.
EXT3 FS on mmcblk0p1, internal journal
Setting the system clock.
Cleaning up ifupdown....
Loading kernel modules...FATAL: Could not load
/lib/modules/2.6.26-at13/modules.dep: No such file or directory
Checking file systems...fsck 1.41.3 (12-Oct-2008)
done.
Setting kernel variables (/etc/sysctl.conf)...done.
Mounting local filesystems...done.
Activating swapfile swap...done.
Setting up networking....
Configuring network interfaces...net eth0: SMSC911x/921x identified at
0xc9000000, IRQ: 64
done.
Setting up ALSA...done.
INIT: Entering runlevel: 2
Starting enhanced syslogd: rsyslogd.
Starting system message bus: dbus.
Starting OpenBSD Secure Shell server: sshd.
Preparing /var/run/firebird/2.0...done.
Starting internet superserver: inetd.
Starting periodic command scheduler: crond.
Starting web server: apache2apache2: Could not reliably determine the
server's fully qualified domain name, using 127.0.0.1 for ServerName
.
fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
fsl-ehci fsl-ehci.1: irq 35, io mem 0x43f88200
fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
fsl-ehci fsl-ehci.2: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.2: new USB bus registered, assigned bus number 3
fsl-ehci fsl-ehci.2: irq 37, io mem 0x43f88000
fsl-ehci fsl-ehci.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected

X: warning; process set to priority -1 instead of requested priority 0

X.Org X Server 1.4.2
Release Date: 11 June 2008
X Protocol Version 11, Revision 0
Build Operating System: Linux Debian (xorg-server 2:1.4.2-10.lenny3)
Current Operating System: Linux debian 2.6.26-at13 #4 PREEMPT Thu Jan 20
11:38:40 JST 2011 armv6l
Build Date: 25 September 2010 02:52:58PM

Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Thu Oct 6 14:51:17 2011
(==) Using config file: "/etc/X11/xorg.conf"

X: warning; process set to priority -1 instead of requested priority 0

Fatal server error:
Server is already active for display 0
If this server is no longer running, remove /tmp/.X0-lock
and start again.

xf86optionListCreate: count must be an even number.
State: S_UNTOUCHED Action: No Action Button: 0
State: S_TOUCHED Action: No Action Button: 0
State: S_LONGTOUCHED Action: down Button: 1
State: S_MOVING Action: No Action Button: 0
State: S_MAYBETAPPED Action: click Button: 1
State: S_ONEANDAHALFTAP Action: down Button: 3
[config/hal] couldn't initialise context: (null) ((null))



---------------------------------